We've discovered this great article on How to Install a Bathtub Yourself below on the internet and thought it made good sense to relate it with you here.
Installing a tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open a wall surface to remove the old tub and also position the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need an assistant to vacate the old tub and also set in the new one. See to it you have certified on your own for the job as well as are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your restroom if you have already gotten a brand-new tub as well as do not require to transform the setup of your previous water system pipes.
Your devices and also material checklist ought to make up the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be rather bothersome because of the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the staying water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Using both wood boards under its feet, position the bathtub in the needed placement. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water supply and also check all joints as well as new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling as well as securing around the bathtub ought to wait till the bath tub has been utilized at the very least once as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines are in place between the tap and also the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The former kind should be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, creating the water to penetrate the wall between the bathroom and also the tiling, bring about complications with dampness and possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, as well as can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very curious about How to Install a Bathtub Yourself and I am praying you enjoyed reading my article. Remember to take the time to promote this blog entry if you enjoyed reading it. Thank you so much for going through it.
This Site